Thursday, August 16, 2012

Weaver's Delight Restoration is Finished

My goodness, it has been about three weeks since I last posted anything about anything!  Chest pains and low blood pressure have taken all my energy for anything but going to work.  I had a stress test done today, after seeing my cardiologist last week.  Hopefully I will get some answers soon, and start feeling better.

I have been taking some small steps with finishing the loom restoration during the last month.  The good news is that I started weaving on it today!
The pattern that I decided to try first is the Double Seed Rug, also know as Chicken Tracks, from the Rag Rug Handbook, pg 69.  I'm using a 12 dent reed, and I wound 27 ends per section.  The orange section was where I was spreading the warp and trying to get the tension adjusted.  The green is my hem.  Now I need to get some fabric cut.  I still need to clean up the shuttles and tubes for the warp, so this first rug may be hand woven with a regular rag shuttle.

The cast iron parts at the bottoms of the back posts are there to bolt the loom to the floor.  This photo is evidence of why they are needed.  The papers on the floor by the loom were halfway UNDER the loom when I started weaving.  The loom moved about 1 1/2 to 2 feet while weaving the warp spacers and the hem!  I am going to have to get Bob's help turning the loom and bracing it against the foundation with a couple 2x4's.



Sectional warping was a new experience for me.  The spool rack worked well as long as it had weight at the bottom to keep it from tipping over.  I needed all the threads to come into the tension box from a low position, so I ran them under a barbell.
I didn't use the little gadget will all the little holes that came with the loom, because I wanted my threads to go onto the warp beam in a certain order.  I had a short piece of rigid heddle with just the right number of slots and holes for each section.  It worked well for keeping the threads in order.  I wound a few of the sections by myself, but it was pretty hard, so Bob helped with the cranking for the rest of them.

 This shows the correct direction for the straps to wrap around the warp beam.  The buckle ends fall between two of the bars, so the knots don't make any lumps in the warp.  I wound every other section with five groups of three threads in red and four of tan, and then reversed the order for the other sections. 

I cut eight pieces of plastic tubing and slipped them over the pegs to help guide the threads into each section. It kept the warp from catching on the tops of the pegs.

Not having a brake band pretty much stopped any work on the loom.  I had ordered one, but the lady that supplies parts became very ill and was unable to send the part.  I called my good friend Lou, down in Arkansas, and he helped us out with some photos and dimensions for making one.  Bob was able to get some angle iron, rivets, and a steel band from the hardware store and made one.  We had some trouble with the rod that screws into the bracket not having enough threads when we used the spring that came with the loom.  Instead of making a whole new band that was a little longer, Bob just replaced the spring with a shorter one.  The position it is in in the photo is about where it should be with the tension tightened for weaving.  When loosening it to wind warp on the sectional beam, the rod is backed out almost flush with the bracket.









The straps on the loom were in very poor condition, and were wired together in spots.  I contacted an acquaintance of my daughter Becky, and he was able to make new straps.
These are the new short straps.
This is one of the two new longer straps that connect to the picker sticks.
It was actually raining in this photo, and shortly after, we had a downpour that lasted about 20-30 minutes.  Everything is nice and washed outside, and the sun is shining again.

Along with helping me with some of the heavier restoration things, like the brake band, Bob has also been working on a treadle stand for the old Leclerc Jano table loom.  Here, he is working on marking the holes on the lamms.  It should be nice with the little shelves on either side.  It's almost done, except for the lamms and getting some finish on the wood.

4 comments:

  1. I'm so glad you've feeling better. Your weaving projects and your husbands restoration skills are impressive. We've entered into an interesting age and it can be a little scary at times.

    ReplyDelete
  2. First....I am happy that you are feeling better! I know you'd not posted in awhile, but "assumed" life got in the way. ;) Thankfully, you have been taking care of yourself. :)
    My goodness but what a change from the last time we saw the loom! So glad that you have Bob, and friends, that can help you make what you can't buy when needed! Your last photo of the new stand that Bob is making for your table loom is spectacular, too. I love weaving on my Ashford table loom with the stand. Sitting the correct height to weave is so important!
    Again, I am happy to hear that you are feeling better and thank you also for another great post!

    ReplyDelete
  3. I love the treadle stand Bob is making for the Jano. I just received a Jano myself, and immediately thought that it needed a treadle stand! maybe someday!

    ReplyDelete
  4. Hi there,
    I also have a Weaver's Delight loom and I'm in the process of restoring mine so I can use it. I've come a long way this year but I'm still stuck on the picker straps...I cannot seem to find the correct length for these at all. My shuttles won't launch. :( is there any way you could possibly provide the strap lengths for all 4 of your straps and let me know at which length you've buckled each one respectively? That would be an immense help! Thanks...love your blog!

    ReplyDelete